Autor Wątek: [SHB] MSSR as MEM (1967-1968)  (Przeczytany 249 razy)

0 użytkowników i 1 Gość przegląda ten wątek.

Offline Orionid

  • Weteran
  • *****
  • Wiadomości: 21901
  • Very easy - Harrison Schmitt
[SHB] MSSR as MEM (1967-1968)
« dnia: Sierpień 28, 2022, 23:48 »
Source: http://spaceflighthistory.blogspot.com/2021/12/mssr-as-mem-1967-1968.html

MSSR as MEM (1967-1968)
Posted by David S. F. Portree on 12/23/2021


Scary ride: second stage and crew cabin of the Bellcomm minimum Mars Excursion Module (MEM) ascent vehicle. The unpressurized cabin would have included few displays and minimal communications. Image credit: Bellcomm/NASA.

The NASA Planetary Joint Action Group (JAG) saw the addition of the Mars Surface Sample Returner (MSSR) probe to the piloted Mars/Venus flyby mission scenarios it studied in 1966 as a pivotal innovation. Before the advent of the MSSR, the piloted flyby mission appeared to be increasingly threatened by successful robotic flyby missions. The MSSR, members of the Planetary JAG contended, gave the piloted flyby mission an added capability that could not be reproduced by a wholly robotic Mars mission.

The piloted flyby spacecraft would have released the MSSR perhaps 10 days before Mars close encounter. A rocket motor on the MSSR would have boosted it toward Mars, enabling it to reach the planet and land at a preselected site several hours before the piloted flyby spacecraft arrived.

The crew on board the piloted flyby spacecraft would have used a variety of sample collectors on board the MSSR to gather about two pounds of Mars surface material and air by remote control as the planet grew ever larger in their viewports. These would have been packed into a three-stage ascent vehicle and launched to the piloted flyby spacecraft.



Partial cutaway of Mars Surface Sample Returner (MSSR) probe. A = Mars intersect trajectory injection stage with toroidal propellant tank; B = sample canister; C = ascent stage with three stages, each with a toroidal propellant tank; D = folded landing leg (one of four); E = aeroshell heat shield; F = toroidal descent stage propellant tank; G = descent stage engine heat shield cap. Image credit: NASA/DSFPortree.

The astronauts on board the piloted flyby spacecraft would have captured the sample canister and ascent vehicle third stage using a boom-mounted docking ring and linked them to a port leading into a hermetically sealed biological laboratory. The MSSR probe would, it was expected, enable analysis of Mars samples within an hour of their collection, helping to ensure that any martian organisms they contained would still be alive.

Phase 1 of the Planetary JAG piloted flyby study ended with distribution of an NASA report on 3 October 1966. The group then began work on Phase 2 of its piloted flyby study. Some members of the Planetary JAG foresaw a rosy future for the concept — they anticipated that MSSR study contracts might be awarded in Fiscal Year 1968 and the piloted flyby mission might become a NASA new start project in Fiscal Year 1969.

Even before the AS-204/Apollo 1 fire (27 January 1967), however, NASA planning for missions beyond Apollo was on shaky ground. Neither the Administration of President Lyndon Baines Johnson nor the Congress supported ambitious plans for post-Apollo spaceflight — for example, a long-term lunar base or humans on Mars. By the summer months of 1967, the fire, racial and anti-war tensions across the country, concerns about the Federal budget deficit, and military setbacks in Indochina had provided opponents of an expansive U.S. future off the Earth with ample justification for curtailing NASA efforts to define its future.

Not all advance planning halted, however. Bellcomm, NASA's Washington, DC-based planning contractor, continued its work as a matter of course. Most Bellcomm studies in the 1967-1969 period aimed to define the shape of the Apollo Program after the first successful piloted lunar landing, as well as that of Apollo's planned successor, the Earth-orbital and lunar Apollo Applications Program (AAP). A modicum of work toward more ambitious goals beyond Earth orbit and the Moon also continued.

In July 1967, for example, Bellcomm planners D. Cassidy and H. London completed a short technical memorandum in which they explored how the MSSR probe might form the basis for a piloted Mars Excursion Module (MEM) lander. Their study kicked off a series of related studies at Bellcomm in the year that followed.

Cassidy and London assumed a 15,000-pound MSSR with a two-stage ascent vehicle capable of launching 80 pounds to a passing piloted flyby spacecraft launched in 1975, 1977, or 1979 on a Mars Twilight flyby path. The "Twilight" mission owed its name to the geometry of its Mars flyby — closest approach to Mars took place over the planet's night hemisphere near the dawn terminator, the line dividing pre-dawn darkness from daylight.

The Bellcomm engineers calculated that MSSR Mars atmosphere entry velocity would reach 32,500 feet per second (fps) in 1975, 34,500 fps in 1977, and 39,000 fps in 1979. As it passed at a shallow angle through the thin martian atmosphere, the automated MSSR would undergo deceleration equal to up to 40 times the pull of gravity on Earth's surface (that is, 40 Gs). To accomplish rendezvous with the passing piloted Mars flyby spacecraft, the MSSR ascent vehicle would have to boost an 80-pound third stage and sample container to 36,000 fps in 1975, 38,000 fps in 1977, and 42,500 fps in 1979.

An MSSR-derived MEM released during piloted Mars orbiter approach to Mars — that is, before the orbiter fired its rocket motors to slow down so that Mars's gravity could capture it into an elliptical orbit with a one-day period — would, on the other hand, in 1978, 1982, 1984, 1985, and 1986 enter the martian atmosphere moving at between 20,000 fps and 25,000 fps. It would decelerate at about 10 Gs, which Cassidy and London judged to be acceptable for an astronaut.



MSSR-derived minimum MEM. Image credit: Bellcomm/NASA.


Two ways of landing on Mars: Direct Entry Mode would see a pair of minimum Mars Excursion Modules (MEMs) and a shelter deployed from a Mars orbiter (labelled "S/C") during approach to Mars. The orbiter would then fire rocket motors to capture into an elliptical Mars orbit. If the orbiter could not capture into orbit, the twin MEMs would abort their landing, fly past Mars, and rendezvous with the orbiter. Entry from Elliptical Orbit would see minimum MEM and shelter separation after the Mars orbiter captured successfully into Mars orbit. Image credit: Bellcomm/NASA.

An equivalent MEM released in Mars orbit would enter more slowly and subject its occupant to a reduced G load while also enabling more precise landing site targeting. The MSSR-derived MEM ascent stage could boost a 900-pound third stage and crew capsule containing a single astronaut to a velocity of 18,000 fps to a rendezvous with the piloted orbiter in an elliptical Mars orbit with a period of one day.

Cassidy and London explained that a separate Bellcomm study, not yet completed when they finished their July 1967 memorandum, had determined that a minimum one-person MEM with a crew capsule weighing as little as 600 pounds without an astronaut on board might be possible. Such a MEM would carry only enough life support consumables to remain on Mars for a short time and no scientific exploration equipment.

Anticipating that a mission so limited might not enjoy much support, they briefly examined one that employed three MSSR-derived landers: a pair of minimum MEMs carrying one astronaut each and an automated one-way cargo lander for delivering 5,500 pounds of life support supplies and science gear. The three landers would touch down near each other so that the two astronauts could meet up and make use of the cargo.



Compared with the MSSR-derived MEM ascent vehicle, the single-seat Mercury spacecraft — shown here with its retrograde propulsion system (bottom, strapped to bowl-shaped heat shield) and red launch escape tower — was large, heavy, and complex. Image credit: NASA.

The study of a 600-pound MEM crew capsule Cassidy and London referenced was performed by M. Skeer in consultation with Cassidy and unnamed McDonnell Aircraft engineers. Skeer, a newcomer to Bellcomm in 1966, summed up results of his study in a technical memo dated two months after the Cassidy and London study.

Skeer explored whether the design of the one-man McDonnell-built Mercury capsule, which carried six astronauts on suborbital and orbital missions in 1961-1963, might contain weight-saving lessons for designers of an MSSR-derived MEM ascent vehicle. The 4600-pound Mercury capsule, he explained, was a good choice for his study because, like the minimum-mass MEM ascent vehicle, it had relatively simple mission objectives compared with the Gemini or Apollo Command and Service Module (CSM) and Lunar Module (LM) spacecraft.

The minimum MEM would descend from a spacecraft in a highly elliptical Mars orbit with a period of from 24 to 48 hours. A spacecraft in such an orbit would be bound loosely by Mars's gravity, so would require minimal propellant expenditure to depart the planet when the time came to return to Earth. Descent from the highly elliptical orbit to the surface of Mars would last about six hours and return from the surface of Mars to highly elliptical orbit would require about two hours.

Skeer eliminated 47% of Mercury's weight immediately by deleting the 1119-pound launch escape tower, 315-pound heat shield, 317-pound retrograde propulsion system (used to deorbit the Mercury capsule), landing systems and recovery gear together weighing 343 pounds, and 51 pounds of experiments. He then treated remaining Mercury systems in detail. He wrote, for example, that McDonnell engineers had told him that the 75-pound Mercury couch could be trimmed to 15 pounds. Skeer arrived at a total MEM ascent stage weight of 738 pounds including a 170-pound astronaut.



Minimum MEM entry and landing. Image credit: Bellcomm/NASA.


Useful payload: two-stage minimum MEM ascent vehicle. Image credit: Bellcomm/NASA.


Minimum MEM liftoff, ascent, and orbital insertion. After rendezvous in Mars orbit the single astronaut would fly the capsule into a hangar on the Mars orbiter or would abandon the capsule and enter the Mars orbiter by spacewalking. Image credit: Bellcomm/NASA.

The MEM cabin would provide just 92 cubic feet of volume for the astronaut — 26 cubic feet less than the snug Mercury cabin. A "plastic shroud" measuring just 30 inches wide by 60 inches long, it would be neither pressurized nor insulated. Skeer estimated that it could weigh as little as 200 pounds, about 415 pounds less than the Mercury cabin structure. The cabin's small volume would prevent the astronaut from moving much; Skeer argued that astronaut immobility would simplify ascent stage guidance and control by avoiding center-of-gravity shifts.

The astronaut packed into the coffin-like MEM cabin would rely for life support on a 40-pound space suit with a 100-pound life support backpack containing sufficient life support consumables for 12 hours of operations. This combination would replace a Mercury cabin life support system weighing 248 pounds.

Skeer briefly examined a two-person minimum MEM with a descent stage not based directly on the piloted flyby MSSR. This would, he wrote, have a total weight of less than 35,000 pounds. Of this, 1360 pounds would comprise the MEM ascent stage and crew. He clearly favored the single-person minimum MEM, however.

Skeer subsequently conducted a pair of follow-on studies of MSSR-derived piloted spacecraft. The first, completed on 8 May 1968, looked at a 4064-pound MSSR-derived two-person surface shelter that would enable a two-week Mars surface stay by astronauts landed separately in a pair of MSSR-derived minimum MEMs. Expendables supporting the two-week stay — mostly for life support and power generation — would account for 1053 pounds of the shelter's weight.



Cutaway view of MSSR-derived Mars surface shelter. Image credit: Bellcomm/NASA.


Plan view of MSSR-derived Mars surface shelter. Image credit: Bellcomm/NASA.

The 575-cubic-foot shelter would include a 60-cubic-foot airlock accessed from the martian surface by a "hoist" (apparently a one-person open elevator platform). A pair of 25-cubic-foot compartments accessed from within the shelter (not from the airlock) contained four complete space suits so each crewmember could have a spare. A laboratory area accounted for 50 cubic feet of the shelter's volume.

Scientific exploration equipment accounted for 1460 pounds of the shelter's weight. This included a single 367-pound one-person surface rover or flyer with a total range of 420 kilometers, 77 pounds of multiband photography/radiometry equipment, a 107-pound shelter-mounted drill capable of reaching a depth of 30 meters, 100 pounds of "surveying tools," a 250-pound "Emplaced Science Station" and three "satellite science stations" (total weight 140 pounds) meant to be left behind on the martian surface, and "local sampling and environmental equipment" weighing a total of 395 pounds. The shelter's pressurized cabin would contain 50 pounds of equipment for geologic analysis. (Skeer made no reference to return of samples in the two minimum MEM vehicles; presumably sample analysis on Mars was meant to replace return of samples to Earth.)

Skeer's second follow-on study, a more detailed examination of the minimum MEM ascent stage dated 8 July 1968, sought to identify "fruitful areas of technological research and development needed for evaluation and future program planning options." He argued for development of new propulsion systems capable of burning new high-energy propellants (for example, fluorine-LOX/methane), compact and lightweight refrigeration systems for long-term storage of such propellants, and development of new lightweight materials to permit further minimum MEM weight reduction.

He also noted that flights of MSSR probes during piloted flyby missions could be seen as test flights of minimum MSSR technology. Unfortunately, by the time Skeer completed his second follow-on study, work within the NASA Planetary JAG toward a piloted flyby with MSSR probe had been largely abandoned for nearly a year.


Sources

"MSSR/MEM Commonality - Case 233," D. E. Cassidy and H. S. London, Bellcomm, Inc., 19 July 1967.

"Preliminary Sizing of a Mars Excursion Module Ascent Capsule Based on Mercury Spacecraft Design - Case 233," M. H. Skeer, Bellcomm, Inc., 25 September 1967.

"Preliminary Mars Excursion Module Shelter Design - Case 730," M. H. Skeer, Bellcomm, Inc., 8 May 1968.

"Mars Excursion Module Ascent Propulsion Stage Design," M. H. Skeer, Bellcomm, Inc., 8 July 1968.

More Information
(...)
« Ostatnia zmiana: Wrzesień 11, 2022, 13:20 wysłana przez Orionid »

Polskie Forum Astronautyczne

[SHB] MSSR as MEM (1967-1968)
« dnia: Sierpień 28, 2022, 23:48 »